Template:Menu Sizing and protection of conductors: Difference between revisions

From Electrical Installation Guide
(Updated chapter Q name in menu templates)
m (1 revision imported: move to MW1.39)
 
(6 intermediate revisions by 2 users not shown)
Line 1: Line 1:
<div class="noprint">
<includeonly>
<div class="template_div">
<!---------- modify the chapter letter below, to adapt to each chapter ---------->
{| class="template_table"
{{#vardefine:letter|G}}
| | [[General rules of electrical installation design]]
<!---------------------------------------------------------------------------------------------------->
|-
{{#isin:{{#hierarchyParent:{{#titleparts:{{FULLPAGENAME}}}}|{{MediaWiki:eig-hierarchy}}|hierarchyargtype=wikitext|link=none}}}}
| | [[Connection to the MV utility distribution network]]
{{#set:Has chapter letter={{#var:letter}}}}
|-
{{#vardefine:menuMsg|eig-ch-menu-{{#var:letter}}}}
| | [[Connection to the LV utility distribution network]]
{{#sideSummary:{{#var:menuMsg}}}}
|-
{{ch-category|{{#var:letter}}}}[[Category:eig-content-pages]]</includeonly><noinclude>[[Category:eig-ch-menus]]<templatedata>
| | [[MV and LV architecture selection guide for buildings]]
{
|-
"params": {},
| | [[LV Distribution]]
"description": "This template is used to add common information to pages of a same chapter: semantic property for parent page, chapter category, and sidemenu"
|-
}
| | [[Protection against electric shocks and electrical fires]]
</templatedata>
|-
</noinclude>
| id="chapter" | [[Sizing and protection of conductors]]
|-
| class="selected" |
* [[Conductor sizing and protection]]
** [[Conductor sizing: methodology and definition]]
** [[Overcurrent protection principles]]
** [[Practical values for a protective scheme]]
** [[Location of protective devices]]
** [[Conductors in parallel]]
* [[Practical method for determining the smallest allowable cross-sectional area of circuit conductors]]
** [[General method for cable sizing]]
** [[Recommended simplified approach for cable sizing]]
** [[Sizing of busbar trunking systems (busways)]]
* [[Determination of voltage drop]]
** [[Maximum voltage drop limit]]
** [[Calculation of voltage drop in steady load conditions]]
* [[Short-circuit current]]
** [[Short-circuit current at the secondary terminals of a MV/LV distribution transformer]]
** [[3-phase short-circuit current (Isc) at any point within a LV installation]]
** [[Isc at the receiving end of a feeder as a function of the Isc at its sending end]]
** [[Short-circuit current supplied by a generator or an inverter]]
* [[Particular cases of short-circuit current]]
** [[Calculation of minimum levels of short-circuit current]]
** [[Verification of the withstand capabilities of cables under short-circuit conditions]]
* [[Protective earthing conductor (PE)]]
** [[Connection and choice for protective earthing conductor]]
** [[Sizing of protective earthing conductor]]
** [[Protective conductor between MV/LV transformer and the Main Low Voltage Switchboard (MLVS)]]
** [[Equipotential conductor]]
* [[The neutral conductor]]
** [[Sizing the neutral conductor]]
** [[Protection of the neutral conductor]]
** [[Breaking of the neutral conductor]]
** [[Isolation of the neutral conductor]]
* [[Worked example of cable calculation]]
|-
| | [[LV switchgear: functions and selection]]
|-
| | [[Overvoltage protection]]
|-
| | [[Energy Efficiency in electrical distribution]]
|-
| | [[Power Factor Correction]]
|-
| | [[Power harmonics management]]
|-
| | [[Characteristics of particular sources and loads]]
|-
| | [[PhotoVoltaic (PV) installation]]
|-
| | [[Residential premises and other special locations]]
|-
| | [[ElectroMagnetic Compatibility (EMC)]]
|-
| | [[Measurement]]
|-
|-
|}
</div>
[[Category:Chapter - Sizing and protection of conductors]]
</div>

Latest revision as of 13:45, 26 January 2024

This template is used to add common information to pages of a same chapter: semantic property for parent page, chapter category, and sidemenu

Template parameters

ParameterDescriptionTypeStatus
No parameters specified